Naujas žirklinis automobilių keltuvas TyreON TSC5000X2A Alignment scissor lift - In floor - Free wheel liftin

Capacity 5000 kg - In floor
Liftheight 216 cm
Runway LxW 530 cm x 60 cm
Drive motor 3,5 kW (C16A)
2nd Scissor 4T - H43cm - L150 -- 200 cm
► LED8P runway lighting
► Rails for optional rolling jack
► Hose sets + floor covers
Installation depth 31 cm
Foundation C20/25 - 600 x 300 x 20 cm
Lifting/Lowering About 70 s
On floor version Available with OFK1 on floor kit
Voltage 400V
Color Anthracite gray / light gray
Hydraulic oil is not included 20 L TyreON HV-ISO-32 is optional

Inground installation alignment scissor lift with free wheel movement capability in runways.
Display for reading the status of functions of the alignment scissor car lift.
Most robust and reliable 5T in floor alignment scissor car lift available.
Perfect balanced scissor car lift for accurate wheel alignment with about 1 meter of workspace between the runways.
Large working range from very short to very long wheelbase
Integrated LED lights along the length of the runways
Wheel-free lifting system with extendable lifting platforms
Heavy duty hydraulic pump with load sensing lowering valve
Multi-functional: for inspection, maintenance, repair, wheel alignment, testing of headlights and driver assistance systems, etc.
TyreON TSC5000X2A Alignment scissor lift - inground installation
Suitable for short and long passenger cars (multiple stretch extra large) vans and small lorries
With long scissors and oversized runways
Two hydraulic cylinders for heavy lifting
Manual override for descending in case of power outage (handpump)
Safety valve (overload safety) - No damage to car lift in case of overload
Remote controlled lift of about 2,6 meter or less
Entirely powder coated finish
Required air pressure 8 - 10 bar
Simple installation with system integrated depressurization and runway leveling out procedure
Controller L35,5 xW 37 x H108 (cm)
2nd scissor - Free Wheel system and wheel alignment
With the extra long rear wheel plates and spacious recesses for turntables, the TSC4000X2A is suitable for aligning short and long chassis vehicles up to 5T.
Regular and 3D wheel alignment
Hydraulic free wheel system -4000 kg - Lift height 43 cm
Extendable platforms 150 - 200 cm
Runways with removable shims for turntables
Runways with built-in movable rear wheel plates - mechanically lockable
XL rear wheel plates - 1.8 meter
Safety features - CE-Stop - In Floor alignment scissor lift
Voltage through entire lift and control panel is only 24V
Automatic and accurate syncing function of the runways
CE-Stop: end height switch at 30 cm, additional manual input required for final stage of descending
Lowered descending velocity during final stage and acoustic and optical signal
Hydraulic shut-off valve
Tube failure safety system
Automatic safety lockup - 19 lock positions
Automatic unlocking of safety system (air)
Built-in sensor shuts down engine at maximal level of the alignment scissor car lift
Runways with roll of protection
Alignment scissor car lift - Bonus features as standard
Large working range, high performance
Large working range, high performance
5T Capacity - 5.3meter runways
216 cm Lifting height
Long rear wheel alignment plates and various positions for front wheel turn plates
Free wheel system with extendable platforms including 4 rubber lifting blocks
Complete, equipped with
LED8P runway lighting LED 24V including grilles for protection
Rails for TRJ25A axle jack 2.5T (optional)
Installation material included
Hydraulic tube set
Air tube set
Floor covers
Groundanchors
CE-certification
Alignment scissor lift
 in ground
• EN1493:2010 Vehicle Lifts
• EN 60204-1:2006+AC:2010 Safety of machinery - Electrical equipment of machines - Part1: General requirements
• EN ISO 12100:2010 Safety ofmachinery – general principles for design – Risk assessment and risk reduction
-
TSC5000X2A Alignment scissor lift - In floor - Free wheel lifting system - 5.3 m lightened runways - 5T
The price is excluding VAT and delivery costs.