Išpilstymo linija Tetra Pak Therm Aseptic VTIS

Type of Machine: Direct UHT Treatment unit
Capacity: 15.000 liter per hour
Products: UHT Milk
Temperature Range: 5 - 80 - 140 - holding 4 seconds - 81 - homogenization - 20/25 °C
Holding tube: 4 seconds
Dimensions: ± 11 x 5 x 4,5 meter
Marke: Tetra Pak
Tetra Pak ​​​​​​​​​​​​Tetra Therm Aseptic VTIS line with Tetra Alex TA400 homogeniser. Aseptic processing unit for continuous UHT treatment with direct steam injection. Mainly for heat-sensitive low-acid products such as milk
enriched milk
cream
soy milk
formulated dairy products
ice-cream mix
dairy desserts as well as ESL (extended shelf life) products. Previously used in a milk factory in Europe.The unit is fully automated to safeguard the aseptic status while in production. The operation can be divided into four steps:Pre-sterilizationProductionAseptic intermediate cleaning (AIC)Cleaning in place (CIP)Before production can start
it is necessary to sterilize the aseptic area by circulating pressurized hot water. After sterilization
the unit is cooled down to production temperature. Finally
sterile water is circulated through the product circuit.Production starts by filling the unit with product via the balance tank. The product displaces the water/product mix to the drain or reject tank. A specially designed balance tank and valve arrangement minimizes the amount of mixed product.When an aseptic tank or filling machine is ready
production can start. The product is regeneratively pre-heated to about 80 °C in a Tetra Spiraflo tubular heat exchanger. Instant heating to sterilization temperature takes place in the steam injector by continuous injection of high pressure steam into the product.The product enters a holding tube where it is held at sterilization temperature for the required period of time. The product then enters the flash vessel where the pressure and temperature drop instantly. The excess water in the form of steam is flashed off.For optimal product stability
the product passes through an aseptic homogenizer before final cooling in the heat exchanger.Aseptic intermediate cleaning (AIC) can be performed to prolong the production time between full CIPs. When AIC is selected
the product is displaced by sterile water before cleaning starts. During the AIC sequences
the holding tube is kept at the sterilization temperature
thus keeping the aseptic parts of the unit sterile. The AIC can be performed either with lye only or lye and acid flush. After each production run
the unit undergoes CIP with both lye and acid. If the product supply fails or a stop at a filling machine occurs
the unit goes into sterile water circulation.Standard temperature programs for white milk: 5 - 80 - 140 - holding 4 seconds - 81 - homogenization - 20/25°C.The current line existing out of:High Pressure HomogeniserManufacturer: Tetra PakModel: Tetra Alex 400Capacity: up to 15.000 ltr/h @ 400 barYear: 2016Serial number: 5871116178Motor: 400 V - 50 Hz - 340 A - 200 kW - 1.488 rpmParts of the homogeniser block
2x pistons
pulley on the drivework and hydraulic system are missing
see photos.Expansion vessel for flash cooling with built-in condenserManufacturer: Bujalski in the name of Tetra PakModel: ZBB-11-1Year: 2016Serial number: 160333Capacity: 1.220 literMax. allowable pressure: 3,5 barMin. allowable pressure: -1,0 barMax. allowable temperature: 148 °CMin. allowable temperature: 0 °CWeight: 530 kgDesign code: EN-13445-3:2014Skid 01 (CP11)Centrifugal pump (Alfa Laval LKH-25
11 kW
impellor 205 mm
serial nr: 199787).Centrifugal pump (Alfa Laval LKH-50
15 kW
impellor 190 mm
serial nr: 200136).Flowplate.Control panel (T5844130774
3544-1264).Skid 02 (CP51)Direct heating module with:Steam injector for direct heating of the product.Centrifugal pump (Alfa Laval LKH-25
15 kW
impellor 205 mm
serialnr 200788).Vacuum pump (SIHI
LEMB 161 8Z).Valves
pipes
fittings.Control panel with regulator 01 and 02 (T5844130774
3544-1264)Skid 03Steam feed supply skid with 2x Samson valves and some additional piping and valves.Plate Heat Exchanger:Manufacturer: Tetra PakModel: MS10-SMYear: 2016Serial number: 30109-16228Volume: 250 literPressure: 0/16,0 BarTemperature: 0/150 °CNumber of Sections: 2xPlate heat exchanger for cooling of recirculating water for the condenser in the expansion vessel.Tubular Heat Exchanger 01Manufacturer: Tetra PakModel: C-85Year: 2016Serial number: 1163426 01-21Product: Fluid IIDesign pressure PS Shell 0-16 bar and Tubes 0-40 barDesign temperature Shell 0-180°C and Tubes 0-180°CVolume Shell 352,4 liter and Tubes 243,4literTest pressure PT Shell 25,6 bar and Tubes 64 barTubular Heat Exchanger 02Manufacturer: Tetra PakModel: C-85Year: 2019Serial number: 1193240 01-11Product: Fluid IIDesign pressure PS Shell 0-20 bar and Tubes 0-40 barDesign temperature Shell 0-180°C and Tubes 0-180°CVolume Shell 187 liter and Tubes 126,6 literTest pressure PT Shell 32 bar and Tubes 64 barExcluded in the UHT:Product balance tank with level control and product bowl.Flow meter for water.Flow meter for product.Brazed plate heat exchanger for heating in the water circuit.Batch header tank CIP dosing system.Several pipes
bends
valves
internal signal wiring
pipes for signal wiring and fittings required for the assembly of the UHT system.Frequency converters.Main Control panel with PLC control and TPOP human-machine interface (HMI).Technical documentation.Missing in the homogeniser:Parts of the homogeniser block
2x pistons
pulley on the drivework and hydraulic system are missing
see photos